615
edits
Changes
m
no edit summary
* '''Crown caps (29 mm)''' - For capping bottles with 29 mm openings (such as Champagne-style bottles and 375 mL half-Champagne bottles), you will need to source a 29 mm bell and 29 mm caps, which are non-standard. Many 29 mm bottles are both capable and corkable. For cork and capping, see below.
* '''Swing tops''' - Many swing tops are thicker glass and are therefore well suited for higher carbonation beers. Swing tops also allow for easy venting of carbonation if the beer carbonates more than desired/anticipated. Due to the soft gasket (and possibly plastic top piece holding the gasket for some bottles), the same concerns regarding cleaning difficulty and cross-contamination apply to swing tops as to other plastic parts used after the hot side when brewing both normal and 'funky' beers. If you don't want your normal beers exposed to the micro-organisms in your funky beers, we recommend not using the same swing tops for bottling both types of beer, jusrt as we recommend keeping seperate sets of plastic equipment used for fermentation and transfer of fermented beer when brewing both clean and 'funky' beers. Some express concern about long term aging in swing tops and the possibility of swing tops not being as impermeable a barrier to O2. If you are concerned about this they it may be better to not use swing tops for long aged beer. At this time we are unaware of any comparisons of swing tops and other closure mechanisms regarding their susceptibility to O2 transfer during extended aging to give a firm answer as to whether swing tops allow more O2 ingress than other closures or not .
* '''Cork and cage''' - Corking and caging can be used for both champagne-type bottles and the brown glass 'fat-lipped' Belgian bottles, both of which are generally thicker glass and rated for higher CO2 pressure. Generally corking and caging is used for bottles with 29 mm openings, though some have cork and cage finished bottles with 26 mm openings. Make sure your bottle can take corks before using it. Corking and caging does require some more special equipment. Most wine corkers are designed to push the cork all the way into the bottle, which is not what you want. Brewers will at least want a [[Floor Corker|floor corker]] for standard wine bottling, which can be modified to control the cork depth. Bench corkers such as the Colonna capper/corker work as well. Champagne floor corkers are available and make this easier, though they are more expensive. It is difficult to control the exact depth of the cork with a two arm corker, and we do not recommend this for corking and caging. The following gives a step by step process for corking and caging with a non-champagne floor corker. For a more detailed description with pictures, see [http://horscategoriebrewing.blogspot.com/2013/11/corking-your-homebrew.html Dave Janssen's blog post about corking]. The more common floor corkers work by both compressing the cork and pushing it into the bottle with the movement of the arm. In order to leave the cork partly exposed, and to control the exposed cork level, place a standard carboy bung on the rod which pushes the cork. This positioning can be adjusted as needed. Push the cork into the bottle until you reach the bung, then bring the arm all the way up. Remove the bung and lower the spring-loaded pedestal holding the bottle. Then, while holding the bottle with one hand, lower the corking arm completely and bring the bottle down, letting the cork be pushed fully out of the compression section of the corker. Play around with cork depth to find the right amount for you for ease of removal based on your corks, bottles and carbonation levels. The amount of cork sticking out should be more than how it appears when it is caged, as the cork is vertically compressed or 'mushroomed' during the caging process. This mushrooming can be accomplished by hand, though be aware that flaws in the bottle may cause the neck to break, which would be a very dangerous situation if you are applying the downward force by your hand. It can more easily and safely be applied with a bench capper. Put the cage on the cork and compress both with a bench capper. Hold the bench capper arm in place with your shoulder/armpit, leaving both hands free to orient and twist the cage. Special cage twisting tools are available, though sharpies or some interchangeable screwdrivers are about the right size. You could also use twist lock pliers if you have them around.
* '''Cork and cap''' - Corking for cork and cap closures can also be used on champagne-style bottles, which are a good source of high-pressure bottles for brewers. Corking and capping is much more straightforward as the cork is pushed entirely into the bottle. Generally cork and cap closures are used on bottles with 29 mm openings, though some have done this with 26 mm bottles. Make sure your bottle can handle corks before using them for a cork and cap finish. Although the cork depth is not as important as in corking and caging, the cork still must be far enough into the bottle to not interfere with the cap. Bench corkers are recommended for corking and capping as they allow better control of cork depth than two arm corkers and bench corkers allow the cork to be easily depressed further if it is not far enough into the bottle. For 29 mm bottles, you will also need a 29 mm bell and 29 mm caps for capping.
* '''Kegging''' -