Difference between revisions of "Eccentric Beekeeper Bulldog"
(→Parts List) |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 24: | Line 24: | ||
* [http://www.amazon.com/gp/product/B007GDY3CU?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s00 Control Devices CR Series Brass Pressure Relief Valve, 0-100 psi Adjustable Pressure Range, 1/4" Male NPT] | * [http://www.amazon.com/gp/product/B007GDY3CU?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s00 Control Devices CR Series Brass Pressure Relief Valve, 0-100 psi Adjustable Pressure Range, 1/4" Male NPT] | ||
| − | * [http://www.amazon.com/gp/product/B003GSL35O?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s00 Stainless Steel Pipe Fitting, Reducing Bushing, 1/2" NPT Male X 1/4" Female] | + | * '''2x''' [http://www.amazon.com/gp/product/B003GSL35O?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s00 Stainless Steel Pipe Fitting, Reducing Bushing, 1/2" NPT Male X 1/4" Female] (one for the PRV and one for the corny post adapter) |
* [https://www.brewhardware.com/product_p/cross12.htm Stainless Steel Pipe Fitting, 4-Way Cross, 1/2 NPT Female] | * [https://www.brewhardware.com/product_p/cross12.htm Stainless Steel Pipe Fitting, 4-Way Cross, 1/2 NPT Female] | ||
| Line 47: | Line 47: | ||
===Additional Articles on MTF Wiki=== | ===Additional Articles on MTF Wiki=== | ||
* [[Barrel]] | * [[Barrel]] | ||
| + | * [https://www.facebook.com/groups/MilkTheFunk/posts/6161706940524135/ Thomas Rasmussen's DIY homebrew bulldog post on MTF.] | ||
===External Resources=== | ===External Resources=== | ||
Latest revision as of 19:49, 21 September 2022
The Eccentric Beekeeper Bulldog is a homemade bulldog for racking beer out of barrels using CO2 pressure. See this page for other barrel racking canes.
Overview
The bore-through compression fitting allows the racking wand to pass completely through the fitting making the depth adjustable to prevent sediment transfer.
Adjustable emergency pressure release.
Triclover attachment to rubber bung adapter.
The triclover rubber bung adapter lets me use the same Bulldog racking wand for Sanke fermenter kegs with barrels.
An inside view shows the simple "works" within the triclover fitting, liquid inside the wand and gas outside the wand. The standard stainless steel compression rings/sleeves in the bore-through compression fitting have been replaced with silicone o-rings which seal with minimal tightening on the nut and never attach to the tubing permanently. These replacement o-rings allow the racking wand to slide up and down through the compression fitting while maintaining the seal.
Parts List
- Stainless Steel Racking Cane, 3/8" OD x 30" Long (people have reported that some other 3/8" racking canes are too wide for the fittings; see this thread)
- 2x Stainless Steel Pipe Fitting, Reducing Bushing, 1/2" NPT Male X 1/4" Female (one for the PRV and one for the corny post adapter)
- Cornelius-Type Gas Side Plug, P53 - This no longer includes the needed Universal Poppets (our item L92) or Ball Lock O Rings (item D12). You will need one L92 and one D12 in addition to this post to complete your male in gas fitting.
- 2x 2" Tri Clover Compatible X 1/2" Male NPT, TC20M12 (one for the cross and one for the bung; a barbed adapter might be easier to slide the bung onto).