13,591
edits
Changes
→Contamination Concerns
==Contamination Concerns==
When working with lactic acid-producing bacteria, the brewer’s goal is usually to attain clean-tasting sourness, while obtaining desirable flavor contributions from these bacteria, and simultaneously minimizing off-flavors. It should be noted that off flavors span the range from undesired by most, to desirable to some. For example, isovaleric acid is a compound known for its footy aroma that would be considered an off flavor in many beers, yet it gives a highly desired flavor to certain French cheesesand is aceptable by some in small amounts in beer.
With that said, contamination issues are among the biggest challenges when pre-souring wort with ''Lactobacillus''. This is because ''Lactobacillus'' does not fully ferment wort by itself (see [[100%25_Lactobacillus_Fermentation|100% ''Lactobacillus'' fermentation]]). When yeast fully ferments wort into beer, alcohol, hops, and a low pH all work together to prevent most spoilage microorganisms from contaminating the beer (although contamination can certainly happen with beer spoilage microbes such as ''Brettanomyces'', ''Pediococcus'', etc.) <ref>[http://suigenerisbrewing.blogspot.com/2014/02/fact-or-fiction-can-pathogens-survive.html "Fact or Fiction? Can Pathogens Survive in Beer?" Sui Generis Blog. 02/18/2014. Retrieved 11/10/2016.]</ref>. When fermenting with ''Lactobacillus'' by itself, either no alcohol is produced or not enough alcohol is produced to have an antimicrobial effect. Usually hops are not used when souring wort with ''Lactobacillus'' because even small amounts of hops completely inhibit most commercial strains, but they also inhibit some spoilage microorganisms. The high available sugars, warm temperatures typically used in souring wort, and a lack of alcohol and hops therefore increases the chances for contamination during souring wort with ''Lactobacillus''.
If a yeast contamination produces a significant amount of alcohol during the souring process, then this presents a problem when it comes to boiling. Although 100% pure ethanol boils at 173.1°F/78.4°C <ref name="boiling_of_alcohol">[http://chemistry.about.com/od/moleculecompoundfacts/f/What-Is-The-Boiling-Point-Of-Alcohol.htm Boiling temperature of ethanol]</ref>, the lower the concentration of ethanol in the wort (technically beer at this point if it has been fully attenuated by yeast), the higher the temperature required for boiling off the ethanol. For example, at 5% ABV it takes approximately 197°F/92°C for the ethanol to boil <ref>[http://www.clawhammersupply.com/blogs/moonshine-still-blog/12243869-making-moonshine-still-temperature Making Moonshine: Still Temperature. Retrieved 01/11/2016.]</ref><ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1212116758816536/?comment_id=1212140998814112&comment_tracking=%7B%22tn%22%3A%22R%22%7D Conversation with Russell Carpenter on MTF. 01/11/2016.]</ref>. Time is also required to boil off the ethanol, so this may not be as big of a concern as it first appears (''warning: vaporized ethanol is highly flammable)''. Another and perhaps more important consideration is that boiling and high heat pasteurization temperatures can have a negative effect on the flavor of fermented beer. Beer already has anti-bacterial properties, such as low pH, presence of alcohol, and hops (although hops may not be present in wort being soured), so higher pasteurization temperatures aren't necessarily required for beer. For these reasons, the beer industry commonly heat pasteurizes beer at '''140°F/60°C for 15 minutes''', and this is also adequate for pasteurizing soured wort that accidentally fermented do to yeast contamination <ref>[http://www.sciencedirect.com/science/article/pii/S0023643806002854#bib16 A suitable model of microbial survival curves for beer pasteurization. Sencer Buzrul. 2006.]</ref>. Although the yeast will be killed during the pasteurization, so will the ''Lactobacillus'', and the brewer can trust that equipment downstream shouldn't get contaminated. Other options are to simply dump the batch and start again with a pure culture of ''Lactobacillus'', or do not pasteurize and let the ''Lactobacillus'' live. If the ''Lactobacillus'' is not pasteurized and allowed to live, the soured wort/beer should be treated with care so that it does not contaminate the rest of the brewery (see [[FAQ#Do_I_need_separate_equipment|'Do I need Separate Equipment?' FAQ]]).
Boiling soured wort that hasn't had an accidental yeast contamination (and thus still has a high specific gravity) probably has less of an effect on the flavor than it does on fully fermented beer. Other than lactic acid, the flavor components that different strains of ''Lactobacillus'' produce are not well defined, so it will be difficult to determine if boiling soured wort will have a negative impact. However, brewers who boil kettle soured wort don't often report that the boiling causes flavor issues <ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1464590560235820/?comment_id=1465040723524137&reply_comment_id=1465146946846848&comment_tracking=%7B%22tn%22%3A%22R4%22%7D Conversation with Bryan from Sui Generis blog on MTF regarding boiling soured wort. 11/10/2016.]</ref>.
==Concerns about Dimethyl Sulphide (DMS)==