Alternative Bacteria Sources

From Milk The Funk Wiki
Revision as of 22:35, 15 October 2016 by R.Givens (talk | contribs)
Jump to: navigation, search

Sources for Lactic Acid Bacteria, especially Lactobacillus, are available in various forms such as unpasteurized products and probiotics. This page contains a list of sources that Milk The Funk members have experimented with, and their results. Note that the production of products such as probiotics may not be as sanitary as brewing industry yeast manufacturers, so without isolating these bacteria on agar plates, they cannot be considered pure cultures. Methods contained on this page use only materials that a typical homebrewer would have on hand and are geared towards brewers without agar plating capabilities. For information on isolating pure cultures of Lactobacillus with selective media on agar plates, see the Lactobacillus and wild yeast isolation pages.

Yogurt Souring

Mike Karnowski from Green Man Brewery Blueberry Berliner Weisse made from a yogurt starter
Yogurt Souring refers to the method of souring wort using unpasteurized yogurt. Greek yogurt is often made with Lactobacillus acidophilus, a lactic acid producing bacteria that is also associated with some health benefits [1]. Using cultures of L. acidophilus from yogurt reportedly can make a 3.0-3.5 pH sour wort in 24 hours, without producing vomit/fecal flavors and aromas. To sour 5 gallons of wort with yogurt, make a 1 liter batch of unhopped starter wort the day before brew day. Add 2-4 teaspoons of live yogurt to the starter wort. Maintain a 100-110°F (37.8-43.3°C) temperature for about 24 hours. On brew day, and after the 24 hour sour starter is finished, mash and sparge a low IBU wort as normal, boil for a few minutes, and then chill the wort down to 100-110°F (37.8-43.3°C). Pitch the yogurt starter into the wort, and hold the temperature as close to the 100-110°F (37.8-43.3°C) range as possible. Bubbling CO2 through the wort is advised if possible to prevent potential off flavors, but is not required. Within 24 hours, the wort should be down in the 3.x pH range. Boil the wort, adding any hops that the recipe calls for, yeast nutrient, etc., and then cool the wort down to Saccharomyces pitching temperatures. Bob's your uncle! [2]

Brands of Yogurt

In general, non-fat Greek yogurt that is unpasteurized works best. Brands of yogurt that have been reported to be successful with this method:

  • Fage Yogurt [3]
  • Greek Gods [3]
  • Nancy's Yogurt [4]
  • Seven Stars yogurt - Mike Karnowski reported pH of 3.3 after 20 hours @ 110 F. Zero drop in gravity. Clean, soft lactic tartness, with the usual Lacto sulfur aroma that boils off [5].
  • Sigi's Skyr "Yogurt" [6]

Culturing Lactobacillus From Grains

Derek Springer's grain starter
If the brewer wants to use the LAB found naturally on the husks of grains, and doesn't want to risk pitching grains into the entire batch of wort, a starter culture can be made. The benefit of this is that if the culture contains any vomit, fecal, or putrid aromas, it can be thrown away and tried again. If the starter needs to be dumped, try again with a different malt source; microbial populations can vary greatly between maltsters, harvest years, and malt type [7]. The following is Derek Springer's grain starter process [8]:
  1. In a 2L flask make a standard starter wort (1.040 OG).
  2. Add 1/2 tsp 88% lactic acid (should get pH down to 4.0 - 4.5 to help inhibit off-flavor producing microbes).
  3. Add 2 cups uncrushed malt (using acidulated malt is not required).
  4. Top off with carbonated water.
  5. Cap with an airlock.
  6. Keep as warm as you can for 2-3 days, ~110°F is best.
  7. After 2-3 days, strain the grains out using a colander. If no off aromas are detected, pitch the entire starter into the wort using one of the methods described on the Sour Worting page.

See also Microbial Populations on Barley.

Culturing from Kefir

Commercial kefir will have the microbial populations listed on the bottle. Many include Lactobacillus spp. The above process should also work well for home fermented kefir. Pietro Caira from MTF offers this guidance on culturing from commercial kefir products (President's Choice and Liberté brands specifically tested): [9]

  1. Let the kefir warm to room temperature.
  2. Shake the kefir up in the bottle, and add to an unhopped 1 liter starter of ~1.040 SG DME wort (for a 5 gallon batch of beer).
  3. Incubate at a temperature of ~100°F for 24 hours (room temperature may work too).
  4. This results in a starter pH of about 3.2.
  5. Add the entire starter to wort using one of the methods described on the Sour Worting page.

Culturing from Sauerkraut

Pellicle from Alex Loijos's sauerkraut culturing experiment.

Culturing LAB from sauerkraut can be done in much the same way as kefir. This study shows that culturing Lactobacillus from sauerkraut is most likely best done when the sauerkraut is at least 7-14 days old, however after 60 days more acid resistant Lactobacillus cells can be cultured. The following instructions can be used to culture LAB from sauerkraut (and probably from other fermented vegetables) for a 5 gallon batch: [10]

  1. Use 100 mL of at least 14 day old brine, but preferably 60 day old brine, and allow it to warm to room temperature if cold.
  2. Add the brine to a 1 liter starter of ~1.040 DME wort (alternatively use Samuel Aeschlimann's Lactobacillus starter recipe).
  3. Incubate with an airlock at a temperature around ~90°F.
  4. Wait until the starter clears. This may take several days. When it clears, the starter is done. It may show signs of yeast fermentation.
  5. After fermentation finishes, add the entire starter to the wort. Reference the Sour Worting page for further brewing procedures.

Alex Loijos described an interesting process on MTF of culturing successive microbes from a starting batch of sauerkraut. After preparing his sauerkraut, each day he took a sample of the developing brine and pitched it into the same batch of wort. This most likely had the effect of pitching Leuconostoc and Weissella species during days 1-3, and then Lactobacillus species starting on day 7.

The results of this experiment were interesting: "I just tried it cold. It's definitely drinkable!! It tastes like sourdough bread with the tart/salty/bready malt combination. I didn't perceive the viscosity as much and I think it's in part because it's flat that it feels 'thick.' I'm pretty pleased with the surprises along the way during this experiment. Chiefly that there were wild yeast that were capable of 71% attenuation, which I didn't expect! I was just using the kraut brine for souring, and expected I would have to pitch a culture after. Is there anything else like this that provides a pretty much guaranteed full spectrum of wild microbes (yeast and LAB)? Not yogurt, not grain, not coolships in the open air..." ~ Alex Loijos.

Culturing from Probiotics

Some commercial probiotics have been successfully used to produce Lactobacillus cultures (many brands have also failed at providing usable bacteria according to some homebrewers [11]). Probiotics that are classified as "dietary supplements", as opposed to "drugs", may not be as free of contaminates as pure cultures from brewing industry yeast labs [12]. The following probiotics are examples of brands, methods, and results that MTF members have had [13]. Dried forms of Lactobacillus should be stored refrigerated because viability has been seen to decrease as much as 80x when stored at room temperatures [14]. Use only fresh products whenever possible (viability of Lactobacillus drops quickly over time in general), avoid products that have been stored at room temperature (pill and liquid format), and don't bother using expired products [15]. Making a starter is a good way to ensure that the cells are still viable.

See this Sui Generis Blog article on which Probiotics to avoid based on the genera of microbes they contain. Probiotics should have their contents listed plainly on their packaging. Avoid probiotics for animals as they tend to contain organisms that produce off-flavors such as Enterococcus, Clostridium, or Bacillus [16].

Devin Bell has experienced getting good sourness by co-pitching probiotics with L. plantarum with yeast, or even after primary fermentation (also known as the "Reverse MTF Sour"). In the case of pitching L. plantarum after fermentation, the beer turned out like a sour saison, where as co-pitched makes for a better Berliner Weisse or Gose style beer. This has also improved head retention in his beers. Using no hops seems to be required in order to get acid production from the L. plantarum probiotics after primary fermentation. See this thread for details.

General tips on using probiotics:

MTF Member Source Process Results
Matt Firetto Swanson Plantarum Probiotic Pills Starter:

4 capsules Swanson Plantarum probiotic in 1 liter of 1.040 wort fermented in high 70°'s F in garage. After 36hr PH ~3.6 (using cheap wine PH strips) Tasted clean and noticeably sour with fairly strong yogurt like aroma. (not how I would want my beer to smell)

Starter chilled overnight and decanted most liquid before pitching

Single infusion mash all grains at 153°F for 1hr 4.5 gallons strike water 3 gallons sparge water After mashing and sparging, wort heated to 190°F for 10 minutes and cooled to 95°F for souring used 12% acid malt in my mash to help drop the PH before adding the Lacto. Wort PH 4.5 using colorfast strips Wort gravity 1.040 pre boil/pre lacto Pitched decanted lacto starter Flushed Kettle with CO2, covered in plastic wrap and lid

Wort PH ~3.7 gravity 1.038 pre boil/after 24 hrs (using cheap wine PH strips) No off aromas, nice fresh grain aroma. Tastes very clean, sweet, not as acidic as starter. 60 minute boil - 1 oz tettnang at 10 minutes .5oz tangerine peel and nutrient at 5 mins. Post boil gravity 1.040 Pitched US05 at 70°F Fermented for 10 days and kegged at final gravity 1.013

Tasted after 10 days in keg.

Pours with bright white head, which mostly recedes but leaves good lacing. Simple aroma of grain and lactic sour aroma. No off or funky aromas. Taste is very bright with a sharp and simple sourness. No bitterness or hop flavors, but I think the tangerine peel helped to add more complexity to the sour flavors. Light grain character with just a little bit of sweetness.

I also drank this side by side with an Ithaca Cruiser Berliner Weiss. Overall the beers were very similar. The Ithaca beer had a stronger grain aroma and a little less lactic sourdough aroma. Both beers seemed to have about the same perceived level of acidity. The acidity in my beer was just a little brighter than the Ithaca beer, but overall the two were very similar.

David Frank GoodBelly Probiotic Drink Warmed up 2 GoodBelly probiotic drinks to room temperature and then pitched it into unboiled wort (in a purged keg). Sour worted at 95°F. Starting pH was around 4.7 (pre-acidified the mash).

ph at 3.73 after 15 hours

pH at 3.68 after 24 hours

pH at 3.65 after 36 hours

pH at 3.5 after 48 hours - massive co2 (and possibly ethanol) production...when I purged the keg, the beer exploded out. The keg was under around 30psi. Very messy to get it out of the keg and into the kettle.

Beer was then boiled for 20min, chilled and fermented with Kölsch yeast.

Brett Smith GoodBelly Flavored Drinks Probiotic Drink 700ml starter of 1.040 wort. Chill to 95°F. Fill to 1000 with GoodBelly drink. I like the mango as it doesn't seem to leave much aroma at all. Let this starter go for 24 hours. You'll see the massive growth.

Brew beer however you choose. Cool to 100°F. Pitch GoodBelly starter. Let temperature free fall. Check pH in 24 hours, should be 3.4-3.6. I like to let my culture go 36 hours and I'm almost guaranteed 3.4. Then pitch yeast to ferment.

Described this above.
Ed Coffey Swanson's L. plantarum Probiotic Pills Cracked open 3 pills and added to 750ml of DME starter wort, kept at 90°F for 36 hours then pitched into 100°F wort. I've done this twice now, reached a PH of ~3.30 in 48 hours at 95-100°F.
Abel GoodBelly Probiotic Drink Let warm up to temp and pitch straight in. Ph before 5.4, ph at the end was 3.2. Temp held at 95°F for 3.5 days then pitch Sacch and lowered to regular ferment temp.
Viktor Nyman ProViva Superfrukt Probiotic Drink Made a starter of 200 ml juice and 800 ml OG 1040 wort. Fermented at 35°C for a few days, cooled to refrigerator temperature and decanted into a sanitized container. A few days before the brew day, I made a new starter from the decanted bacteria and 500 ml of OG 1040 wort. Fermented at 35°C. Pitched the whole starter into a 15 litre batch. The starter had a starting pH of 4.5 and was under 3 pH in 24 hours. This was when fermenting at 35°C.

The beer itself started at 4.8 pH and I boiled it when it reached 3.2-3.3 somewhere 21 hours later.

Result is clean and lactic without any sign of spoilage bacteria related off flavours (throw up, cheese, butyric acid etc.).

Drew Wham GoodBelly Products (L. plantarum) Their products contain 20 billion cells of the 229v L. planetarium strain per serving. In a 5 gal batch a single serving will reduce the pH to 3.2 in 48-72 hours held at 95°F. Good results in over 12 batches.
Dan Graston Swanson Probiotics 1 capsule in 1 quart of canned starter wort (1.039, 4.44pH, not DME) at 90°F. Starter pH barely dropped for first 24 hours because the Lacto powder just sank to the bottom and never went into suspension, which was unexpected. After rousing, the pH dropped to 3.23 over the next 36 hours. No drop in gravity. Test starter, so no beer was produced.
Allen Stone LactoGG 2 capsules were used in 1 liter of 1.030 wort, and held in high 90°F's for 72 hours before stepping up to 5 liters and pitched after another 7 days. The powder from the capsules fell to the bottom of the starter initially and needed rousing before it started fermenting. I only had test strips, which indicated a ph in the high 3s. I tasted the wort at this point and it had produced some co2, but not much, and a slight tartness. I added Custersianus to ferment out and there has sat for many months. I sampled it recently and it is not great. Slightly tart, but not enough to stand on its own. I would like to do this again with more control, and build a small starter that is pitched into a larger volume of wort, then held at a higher temp. I suspect that because of the makeup of Lacto GG and its ability to survive internal body temp, it may need to work In the low 100s to really go to work. I would say it is a viable option, but not enough info is known at this time to give any suggestions.
Stuart Grant [18] Ethical Nutrients - IBS Support (Australia) Added 120 billion cells. Pitched at 29°C/84°F, and I'm letting it fall to room temp. 20 hours since pitching got to 3.87 pH. Temp has dropped to 20°C/68°F. No change in SG (1.045). After 25 hours, temp down to 19°C and pH down to 3.67. After 35 hours, temp 18°C, pH 3.53, SG 1.045 (unchanged). Lactic flavour is very clean; slightly apple like. It barely tastes tart with all that sugar. After 44 hours, temp 18°C, pH 3.43, SG 1.045 (unchanged). I split the wort in half. First half I boiled for 20 mins with some hops then pitched US-05; second half I did not boil, but added dry hops and Lochristi Brett slurry. The no-boil version which had Lochristi Brett added is down to 1.016 and pH 3.32, while the boiled version pitched with US-05 is down to 1.008 and pH 3.23 (weird that it's lower). Brett version is quite funky with some acetic acid. Clean version is super clean, and ready for bottling soon. Lovely clean sourness. The dry hops come across as lemon zesty. Superbly refreshing! See Stuart's blog post.
Marius Loktu [19] ProbiMage melkesyrebakterier (available in Norway, Sweden, and Denmark) I tend to use 6-8 per 20-25L. (just the content) Turning off heat at about 35C, rack to carboy and pitch content of capsules. Let it naturally reach ambient. Then I pitch yeast after 2-3 days. (always gets me below 3.5 PH) Always sticking with 0 IBU. Have started playing around with co-pitching and pitching lacto after the yeast as well. To get more yeast character from primary. Its capsules. So you just open them up and use the powder inside. It's good not having wet hands doing this. Good results reported.

Using Sourdough Starter

Using Ginger Bug

Matt Spaanem on MTF on using ginger bug: "A ginger bug is just wild yeast and bacteria harvested from ginger root. Just grate up some ginger and add it to some sugar water. After a few days it starts visibly fermenting and you've got your bug... FG 0.995 makes this ~4.3% (OG ~1.028) uncarbed it's a bit dry/puckering/tannic (probably from the tea) with a friendly orangey/coriander flavored tartness and some funk hiding in the background. Ginger follows you throughout and lingers on the tongue. Overall it's good, if a bit dry. I may chaptalize the keg if it still annoys me after its carbed. I should give these bugs a go in an all malt 'real' beer... it was pretty good carbed and dry. I've since used the bug to ferment an actual beer (with malt/grain derived sugars instead of just sucrose) and it was very attenuative and the Brettanomyces made itself known for sure, the Lactobacillus less so, the beer was hopped to 8 IBU. It was in primary for 5 months and has been in secondary for ~2 months to see if anything more happens with it.

As for using ginger bug, I just treat it like any other yeast culture. Once you harvest it from the shredded ginger mixed with sugar water pitch it into a larger batch, use some nutrient. I haven't done any isolating or looking at it under the microscope, but based on behaviors and flavors produced, I believe my bug contains Saccharomyces, Brettanomyces and Lactobacillus (though maybe not Lactobacillus anymore after passing through hopped wort). Obviously you're not guaranteed to catch all of these, it depends on your piece of ginger used, but you're probably likely to catch some yeast and Lactobacillus.

According to Sandor Katz, ginger is also a wild source for Aspergillus oryzae, the mold used to break down rice starches in sake and other rice wines. I tried harvesting it once, it worked, but I couldn't keep my incubation chamber quite warm enough so I also got another mold (probably Aspergillus niger) that produces citric acid and the resulting fermented millet and rice beverage tasted almost exactly like lemon juice... I'll probably try this again now that I have a proper fermentation chamber that I can turn up to 95-100F that should (hopefully) inhibit the citric acid forming mold." [20]

Peppers

See Also

Additional Articles on MTF Wiki

External Resources

References